Patio Umbrella Base – Outdoor Umbrella Stand & Stand Collection

Description

A patio umbrella base is the part of a shade set that nobody photographs and everybody notices the moment it moves. The canopy sells the picture; the base decides whether the canopy is still standing at four in the afternoon on a terrace with a crosswind. Four bases are consolidated on this page, and the difference between them is not colour or surface pattern: it is where the mass comes from. Every patio umbrella base here answers that question with a different material, and the answer is what a buyer is really paying for.

Two of the four are moulded resin half-moon shells. The shape is the same on both: a flat back edge that sits flush against a wall, a planter kerb or a railing, a domed top that slopes down toward the curved front, and a low profile that keeps the weight close to the paving instead of on a stalk above it. One mould carries a radiating ribbed sunburst across the dome with a notched border along the curve. The other carries a raised botanical relief of branches and almond-shaped leaves, with a screw-cap fill plug set into the top beside the collar. Both are finished in matte black, which is the colour that hides scuffs on an outdoor umbrella base, and both are one-piece mouldings with a horizontal seam around the middle, and both carry the same central collar: a vertical sleeve with two scalloped hand knobs at different heights, so the umbrella pole is pinched at two points rather than one.

The third patio umbrella base in the group is a hollow hexagonal block. Six triangular facets slope up from the outer edges and meet at the collar, which gives the base a shallow pyramid rather than a dome. It measures 22 inches across and 14.2 inches to the top of the sleeve, and it is the only base in the group whose mass is added on site: water or sand goes in through the fill point, and the empty shell is light enough to be carried by one person and packed as mail order. Its collar is 2.4 inches outside diameter and comes with two adapter rings, 1.3 inches and 1.5 inches inside diameter, so one block takes a thin beach pole and a heavier commercial pole without a second purchase.

The fourth patio umbrella base goes the other way entirely. It is a cast steel plate, 25 kg, cut as a six-petal flower with rounded lobes that spread the load outward from the collar instead of concentrating it in a disc. The petals are powder coated, in off-white or a dusty pink, with a black gasket where the sleeve meets the plate and a black scalloped knob at the top. On the wheeled version the plate sits on swivel casters, which changes the job it does: a 25 kg patio umbrella base that can be rolled is a base a member of staff will actually move at closing time, and one that cannot be rolled is a base that stays where it was first dropped.

What the four patio umbrella base models share is the collar. Every one of them holds the pole through a sleeve, pinches it with a hand knob, and takes the bending load at the point where the sleeve meets the mass. That is why the collar is worth specifying separately from the base: a heavy plate under a loose sleeve still lets the canopy rock, and a light block under a tight sleeve keeps a small parasol still. On the hexagonal block the interface is written down as dimensions, 2.4 inches outside and 1.3 or 1.5 inches inside with the adapters fitted; on the other three the collar is matched to the pole at sample stage.

All four come out of the same plant in Jiaxing, Zhejiang, 90 kilometres from Shanghai and Hangzhou. One mould shop cuts the resin patterns, one powder line coats the steel petals and the sleeves, and one assembly bench fits gaskets, knobs and casters before packing. That shared line is what makes a mixed patio umbrella base container practical: a buyer can take a pallet of half-moon resin, a pallet of hexagonal blocks and a pallet of steel plates on one order, and the whole shipment leaves through Shanghai or Ningbo. Annual output across the factory runs at roughly 350 to 400 containers.

Choosing between them is a question of where the base stands and who has to move it. Against a wall, on a balcony or on a small city terrace, the half-moon wins because it gives up nothing behind the pole. On an open pool deck or a beach bar where the same base is dragged in and out every evening, the hollow block wins because it ships empty and is filled where it is used. On a hotel terrace with a large cantilever canopy and a fixed layout, the steel plate wins because 25 kg does not need topping up and does not walk.

Key Features

• Three weight systems in one group – cast resin shell, hollow fillable block and a 25 kg cast steel plate, so one patio umbrella base order can cover a balcony, a pool deck and a hotel terrace.
• Half-moon footprint – the flat back edge sits flush to a wall, planter or railing, which is the only way to keep a base out of the walking line on a narrow terrace, and the reason a half-moon patio umbrella base outsells a round one against a wall.
• Two resin moulds – a ribbed sunburst dome and a botanical relief with a fill plug, so the same base geometry can be sold under two visual programmes.
• Hexagonal block with printed dimensions – 22 by 22 inches across, 14.2 inches high, 2.4 inch collar, so the footprint can be checked against a drawing before the order is placed.
• Two adapter rings supplied – 1.3 inch and 1.5 inch inside diameter, letting one umbrella stand base take poles of different gauges without a second collar.
• Cast steel petal plate – 25 kg with six rounded lobes that spread load outward from the collar rather than concentrating it under one disc.
• Casters on the wheeled version – a heavy duty umbrella base that staff can roll away at closing instead of dragging across the paving.
• Hand-tightened collars only – two scalloped knobs per sleeve, no tools, no spanner, nothing to lose on site.
• Ships empty where it can – the hollow block and the mail-packed cartons keep freight weight low; ballast is added after delivery.
• Matte black, off-white or dusty pink – moulded resin in black, powder-coated steel in the two light colours, all with black knobs and gaskets.

Specifications

Weight Systems

Shared Specification

Dimensions, Hexagonal Block

Inches are the original specification on the hexagonal block; the metric column is converted for buyers who quote in centimetres and is not a second tolerance. The umbrella radius is listed as 40 cm on the two resin moulds and 135 cm on the hexagonal block, and is confirmed against the intended canopy at sample stage rather than assumed from the base size.

Materials & Finish

• Moulded resin shell – one-piece casting with a horizontal seam at mid-height, matte black, with the top pattern formed in the mould rather than applied, so the ribs and leaves cannot lift or fade on a patio umbrella base that stays outdoors all year.
• Hollow PE block – blow-moulded polyethylene with six faceted faces, heavy enough in wall section to take water or sand ballast without bulging, and light enough to ship as mail order.
• Cast steel plate – 25 kg body with six rounded lobes, powder coated in off-white or dusty pink, with the coating taken over the lobe edges where a plate normally starts to rust first.
• Collar and sleeve – steel tube with a powder-coated finish, straight through the centre of the mass and welded or moulded into the base depending on the model.
• Knobs and gaskets – black scalloped plastic knobs with a circular centre, plus a black rubber gasket where the sleeve meets the plate, which keeps water out of the joint and stops the two parts fretting.
• Fill plug – screw cap on the botanical half-moon and on the hexagonal block, seated flush so a chair leg or a foot does not catch on it.
• Casters – black swivel casters on the wheeled steel plate, mounted under the lobes rather than at the centre so the base rolls without tipping.
• Colour programme – black on the moulded outdoor umbrella base shells; off-white and dusty pink on the steel plate; the knob, gasket and caster stay black on every version, which keeps the hardware reading as one family.

Assembly & Installation

• Set the base first, then the pole. Place the patio umbrella base on firm, level paving before the canopy is opened; the mass does the work only when the whole footprint is in contact with the ground.
• Seat the half-moon against an edge. Put the flat back edge against a wall, planter or railing so the curved front faces the walking line, then check that nothing under the base rocks.
• Fill the hollow block on site. Take the screw cap off, fill with water or sand, and refit the cap hand-tight. Water is the faster ballast; sand is the heavier one and does not freeze or slosh.
• Fit the adapter before the pole. Slide the 1.3 inch or 1.5 inch ring into the 2.4 inch sleeve to match the pole gauge, then insert the pole until it seats at the bottom of the sleeve.
• Tighten in two stages. Bring the lower knob down until the pole is held, then tighten the upper knob. Two knobs at different heights stop the pole pivoting in the sleeve under gust load.
• Roll, do not drag, the steel plate. On the wheeled version, tilt the plate onto the casters and move it; dragging a 25 kg umbrella stand base across tile scuffs the coating at the lobe edges.
• Check the collar after the first week. A new pole settles into the sleeve; retighten both knobs once the canopy has been opened and closed a few times.
• Store empty and dry. Drain the fillable models before winter storage and leave the cap off for a day so the inside dries, which is what keeps a hollow patio umbrella base from smelling when it is refilled.

Applications

• City balcony and narrow terrace – the half-moon profile gives up no floor behind the pole, so a small patio umbrella base fits where a round one would block the door swing.
• Walled courtyard – the flat back edge sits against the wall and the domed top takes the sun, with the pole running up the wall line instead of through the seating.
• Pool deck and beach bar – the hollow hexagonal block ships empty and is filled on site, so a seasonal operator is not paying freight on water.
• Hotel and restaurant terrace – the 25 kg steel plate is the cantilever umbrella base for a large canopy, holding it without daily topping up, and the wheeled version lets staff clear the terrace at closing.
• Villa garden and patio – two resin moulds let one garden specification use a ribbed base at the house and a botanical base at the pool without looking mismatched.
• Retail and hire stock – mail-packed cartons and a light empty weight make the fillable patio umbrella base the practical one for e-commerce and rental fleets.

Customization

Packing & Logistics

• Steel plate carton – 59 by 71.5 by 5 cm, flat packed, which is the shape that keeps a heavy patio umbrella base at a manageable carton weight.
• Mail packing accepted – all four patio umbrella base models can be packed for parcel networks, with the hollow block shipping empty and the resin shells packed with corner protection.
• Loading – flat plate cartons and nested resin shells load well together, so a mixed container of bases and furniture closes without wasted cube.
• Ports – Shanghai and Ningbo, both within 90 kilometres of the Jiaxing plant.
• Incoterms – FOB, CFR, CIF and EXW.
• Lead time – 25 to 30 days for a 40 ft container, with sample lead time confirmed at quotation.

Nanhu YONGLI Furniture Manufactory is a highly reputable and well-established furniture manufacturer located in Jiaxing City, Zhejiang Province, China. With a strategic location just 90kms away from Shanghai and Hangzhou, the factory boasts unparalleled transport links for efficient distribution and shipping.

YONGLI is a leading Chinese brand with a special emphasis on producing high-quality indoor and outdoor furniture. A testament to its commitment to quality, YONGLI has earned numerous certifications and accreditations over the years, including ISO 9001:2000, BSCI, TUV, BV, SGS, and more than 30 patents.

Over the course of nearly two decades, YONGLI has built a solid reputation in the international furniture manufacturing and export industry. Its wide product range caters to a diverse customer base in various markets, such as the United States, Canada, the United Kingdom, Spain, Japan, Germany, Italy, France, and the Netherlands. Its annual production capacity stands at over 350 40HQ containers.

With its slogan, "Market demands as guidance, persisting in creating bigger value for the customer," YONGLI embodies the principle of human-centricity, prioritizing quality, credit, customer satisfaction, and mutual benefit in all its undertakings. By adhering to the ISO 9001:2000 quality management system, YONGLI continues to improve its manufacturing processes and strive for excellence, ensuring a bright future for both the company and its business partners.

Q: How much weight does a patio umbrella base need? A: It depends on the canopy, not on the base alone. In this patio umbrella base group the fixed options are a 25 kg cast steel plate and two moulded resin half-moon shells, and the adjustable option is the hollow hexagonal block, filled with water or sand on site. The listed umbrella radius runs from 40 cm on the resin moulds to 135 cm on the block, so the cantilever umbrella base question is settled by the canopy rather than by the plate, and the match is confirmed against the canopy at sample stage.

Q: Will the collar fit my umbrella pole? A: The hexagonal block has a 2.4 inch sleeve and ships with two adapter rings, 1.3 inches and 1.5 inches inside diameter, so it takes both a thin beach pole and a heavier commercial pole. On the resin and steel bases the sleeve is matched to the buyer's pole gauge when the sample is confirmed.

Q: Can the fillable base be shipped already filled? A: No. The hollow block ships empty and is filled after delivery, which is the point of the design: freight is paid on the shell, not on water. The fill point takes water for speed or sand for weight, and the cap refits hand-tight.

Q: Why is one half-moon base different from the other? A: They share the same shell geometry, collar and knob set, but one mould carries a ribbed sunburst and the other a botanical relief with a fill plug. That lets one patio umbrella base specification run two visual programmes, at the house and at the pool, without a second tooling cost.

Q: Does a half-moon base have to stand against a wall? A: It does not have to, but it is designed to. The flat back edge is there so the base sits flush against a wall, planter kerb or railing and the curved front faces the seating. Standing it free in open paving loses the advantage of the shape.

Q: Can I put my logo on the base? A: Yes. Silk screen printing is available on the base or the sleeve, and the carton print and inner protection can be set to your specification for mail order. Colour on the steel plate is a powder-coating choice, off-white or dusty pink as standard, with black hardware throughout.